Gloria Fiber Laser Metal Cutting M/c



Briefly, fiber laser light is created by banks of diodes. The light is channeled and amplified through fiber optic cable similar to that used for data transfer. The amplified light, on existing the fiber cable, is collimated or straightened and then focused by a lens onto the material to be cut.


Fiber laser cutting machine is equipped with the most advanced international imported fiber laser source which generates powerful laser focused on objects to cause instant melting and evaporation. Automatic cutting is controlled by digitalized mechanic system. This hi-tech machine has condensed the advance technologies of fiber laser, digital, and precise mechanics.


Applicable to fast cutting on plate or tube in metal, mainly for cutting on SS, Carbon steel, Manganese steel, galvanized plate, alloy plate, rare metal; Widely used in kitchen appliance, electric control box, high-resolute device, mechanical equipment, hardware and metal processing.


Fiber lasers are up to ten times more energy efficient than traditional YAG and Co2 laser systems. And, consuming little to no energy when not active, the annual energy savings can attract government grant funding for industrial energy efficiency programs.

Fiber laser have no mirrors to adjust or align, and no lamps to replace. Maintenance is minimal, so utilization and up-times are maximized. The laser really are designed as shop floor industrial tools.

Fiber laser machine is of low cost which consume very low electricity every hour. It has a lifespan of 1,00,000 hours. Fiber laser is maintenance free and its higher cutting speed and efficiency, speed of cutting plate can reach over 10 meters per minute.

Feature & Technical Advance


Powerful Hardware Configuration

The hardware of closed- loop control system consists of BMC1214 four axis motion card and BCL3724 terminal board. The system adopts high- precision 16- bit DA chip with low- noise and low-drift coefficient signal; Powerful real- time computing power is provided by High-performance ARM processor and FPGA coprocessor; The system can run more fast and smooth owning to 32 large capacity SDRAM memory; Reliable communication can be still achieved in harsh industrial environment due to high- speed differential communication bus. The system is safe, reliable and easy to manage due to coming with its time encryption and decryption function without needing other dongle.


New function of CypCut cutting software
Better speed, better convenience, better security and better use:

Start processing immediately without waiting
It can operate with smooth, high-speed and precision due to leading high-speed NURBS real-time interpolation, and start processing in any position without waiting. Whenever stop, alarm or power-down happens, it can continue to work from the breakpoint.

One Graph, Numerous Processes

You can complete a variety of processes by drawing only one graph. Pre-piercing: Piercing in advance according to your graph. Cutting with a film: Cutting after eliminating the film by stripping process. Secondary cooling: Processing once following immediate cooling along track.

Fast & Practical Scanning Cutting

Now it is possible to scan and cut straight line in any direction, and to naturally and progressively cut circular arc of arbitrary arrangement. We can ensure the tangent between circular arc and scan with smooth and high-speed.

Convenient Seeking- Edge & Locating

Not only capacitive seeking- edge, but also infrared and visual orientation can be easily operated using BCS100. The position and angle can be simultaneously determined in any case mentioned above.


Max Moving Speed 999 mm/s
Max Acceleration 2G
Vibration Elimination Following the front point & edge with easy vibration
Capacitance Mutation Restraint 10%
Min Adaptable Inflexibility Requirement 2 hz
Firmware Upgrade U Disk / Ethernet
DA Resolution 16 Bit
DA zero drift 3 Mv
DA Response Time 0.01 Mv
DA Linearity 0.1%
Positioning Accuracy 0.001 mm
Alarm Information & power Down Save Yes

Applications of Fiber Laser Cutting Machine Gloria Series


The Power, Cutting Thickness & Speed Parameters

Material 300W 500W 750W 1000W 1500W 2200W 3300W 4400W
MS 2.5 5 6-8 mm 8-10 mm 12-14 mm 16-18 mm 20-22 mm 22-24 mm
SS 1.5 3 4 mm 5 mm 6 mm 8 mm 10 mm 12 mm
ALUMINIUM -- -- 1.6 mm 2.5 mm 5 mm 6 mm 8 mm 10 mm
BRASS -- -- 1.6 mm 2 mm 3 mm 3 mm 6-8 mm 8 mm
COPPER -- -- 1 mm 2 mm 2 mm 3 mm 6-8 mm 8 mm
POWER CONSUMPTION 7 9 12 kw 15 kw 18 kw 22 kw 28 kw 34 kw
WATT 220V 220V 220V 440V 440V 440V 440V 440V

Technical Specifications of Gloria Fiber Laser Cutting Machine 510F

Working Area 4 x 4 Feet 4 x 8 Feet 5 x 10 Feet
Laser Type Imported Original Fiber Laser
Laser Wavelength 1070 nm
Laser Output Power 300w / 500W / 750W / 1000W / 1200W
Cutting Tickness 0.2-5 mm
Max. Cutting Speed 30000 mm/min (Adjustable according to defferent cutting thickness)
Position Accuracy ≤ ± 0.04 mm
Minimum Line Width ≤ 0.12 mm
Cooling System Water Cooling
Driving System MITSUBISHI / YASKAWA Servo motor and Drivers
Transmission X axis with imported ball screw, Y axis is imported square rail
Working Voltage 380V / 220V
Total Power Consumed 9 KW / 15 KW
Above Specifications are subject to change without prior notice.